ATVConnection.com ATV Enthusiast Community - Search Results

Search: Posts Made By: jomama
Showing results 1 to 21 of 21
Search took 0.05 seconds.
Forum: Suzuki
06-08-2007, 08:28 PM
Replies: 5
Views: 758
Posted By jomama

clutch control lever problems

I hear ya,

I just spent a couple of ohours puttin my 250 back together.

When I put my pinion shaft back in it has to grab thos teeth on the end of the shaft that comes out of the pressure plate...
Forum: Suzuki
06-07-2007, 10:16 PM
Replies: 5
Views: 758
Posted By jomama

clutch control lever problems

OK, so you pulled the shaft out that pulls the pressure plate on the clutch? Right? Cause I am not sure what the lever is that you are asking about.

You're clutch cable should pull on a arm/...
Forum: Suzuki
06-07-2007, 10:45 AM
Replies: 10
Views: 1,215
Posted By jomama

Spark arestors in exhausts.

I have a silencer on the end of my DG exhaust and I remove the spak arrestor all the time when not needed.

I think the bike runs better without it it's just some places you have to have one for...
Forum: Suzuki
06-06-2007, 06:31 PM
Replies: 5
Views: 758
Posted By jomama

clutch control lever problems

Yes, I have mine apart right now. There are teeth that the lever goes onto right?

If I am reading your question right.

In turn at the bottom of the shaft there are teeth that have to lighn up...
Forum: Suzuki
06-03-2007, 02:55 PM
Replies: 8
Views: 700
Posted By jomama

Crank Balancer

LT80,

With your help I may have found it.

Eureka, there is a dot on the shaft. I guess you just lighn them up and gitt-er done.

I would have never realized there were dots, so thanks for...
Forum: Suzuki
06-03-2007, 02:49 PM
Replies: 8
Views: 700
Posted By jomama

Crank Balancer

Thanks again for your help and I will be asking the mechanic at the dealer tomorrow when I pick up my parts.

I checked and both sprockets do have those stamped dots so I am sure you're right.
...
Forum: Suzuki
06-03-2007, 01:22 PM
Replies: 8
Views: 700
Posted By jomama

Crank Balancer

On second thought there should be a method for placing the cranshaft sprocket on the shaft then aligning the balancer sprocket with it, Right?

Jomama
Forum: Suzuki
06-03-2007, 01:20 PM
Replies: 8
Views: 700
Posted By jomama

Crank Balancer

Hey, I didn't know that. What if I stupidly pulled off the sprocket without checking that first. DOOH!

Thanks,

Joe
Forum: Suzuki
06-03-2007, 12:22 PM
Replies: 8
Views: 700
Posted By jomama

Crank Balancer

Thanks for your reply.

Actually I took off the 2 sprockets on the crankshaft that was held on by the nut so I could clean the threads as the nut stripped off in a freak malfunction.
(previous...
Forum: Yamaha
06-03-2007, 10:25 AM
Replies: 7
Views: 488
Posted By jomama

Warrior problems

My mechanic has tested the stator for me on previous bikes, You'll have to take it in somewhere

Jomama
06-02-2007, 10:31 PM
Replies: 4
Views: 7,482
Posted By jomama

pics

Great pics and vids.

Besides Sand Mountain where else are the pics from?? Especially the ones over xmas and new years.

Jomama
Forum: Suzuki
06-02-2007, 09:25 PM
Replies: 8
Views: 700
Posted By jomama

Crank Balancer

Is there a method or rule on aligning the crank balancer with or against the crankshaft. I have torn apart my LT250 R 87 to fix the crankshaft nut and Later in the day I found my son turning the...
Forum: Yamaha
06-02-2007, 07:44 PM
Replies: 7
Views: 488
Posted By jomama

Warrior problems

Do you have a friend you can borrow a battery from, or just break down and buy a new one. Best bet is to test the battery at a local auto parts store where they can put a load on it and test it.

...
Forum: Suzuki
05-30-2007, 10:53 PM
Replies: 2
Views: 1,623
Posted By jomama

Torque Specs

Sorry I wrote it and it didn't come through.

It's an 87 LT250R and thanks

Joe
Forum: Polaris
05-30-2007, 01:26 AM
Replies: 13
Views: 850
Posted By jomama

trailblazer with no brake preassure

I bought a used Warrior recently and one one of the bolt that hold the brake line on was loose and it did the same thing.

The banjo washers need to be tight, it worked for so good luck.

Joe
Forum: Suzuki
05-30-2007, 01:17 AM
Replies: 2
Views: 1,623
Posted By jomama

Torque Specs

I was hoping some one could tell me what the torque specs are for the clutch basket and installing a new clutch w/springs. Also the torque spec on the crankshaft nut on the clutch side.

Thanks in...
Forum: Suzuki
05-26-2007, 08:58 PM
Replies: 3
Views: 1,249
Posted By jomama

85 LT250R - Loss of power??

I would definitely check the clutch, that would be a good start. I just ordered a new clutch for mine (87 LT250R ) on rocky mountain ATV with springs for 40$.

You are mixing gas right? also are...
Forum: Kids Quads
05-24-2007, 10:30 AM
Replies: 5
Views: 772
Posted By jomama

Buggered spark plug threads

I have done this before, it's not a big deal.
Before you go out and buy the correct tap to re-cut or clean the threads.
Try using the old plug as the tool , good luck.

Joe
Forum: Suzuki
05-23-2007, 10:36 AM
Replies: 0
Views: 1,017
Posted By jomama

crankshaft nut

I was reading an article on the forum about a crackshaft nut that comes loose on several bikes. I have a Suzuki LT250r atv and it did just that.

Left me broke down at Sand Mountain, NV and now I...
05-22-2007, 08:42 PM
Replies: 0
Views: 964
Posted By jomama

Crank Thread pitch

Does anyone know what or how to find out the thread pitch on the crank shaft on a Suzuki lt250r? They are reverse threads and I bought a new nut to put on.
My threads got marred and I need to clean...
05-22-2007, 08:39 PM
Replies: 0
Views: 1,184
Posted By jomama

Thread pitch

Does anyone know what or how to find out the thread pitch on the crank shaft on a Suzuki lt250r? They are reverse threads and I bought a new nut to put on.
My threads got marred and I need to clean...
Showing results 1 to 21 of 21


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.