ATVConnection.com ATV Enthusiast Community - Search Results

 
Search: Posts Made By: sixsixT
Showing results 1 to 25 of 500
Search took 0.12 seconds.
Forum: Yamaha
05-29-2007, 08:14 AM
Replies: 10
Views: 1,105
Posted By sixsixT

Raptor Electrical Problem

I would start with checking the battery connections and the ground connection on the engine and fuses. Have you tried pulling in the clutch when you try to start it?
Forum: Yamaha
05-25-2007, 11:30 PM
Replies: 2
Views: 425
Posted By sixsixT

02 Raptor 660 Problem .. Please Help

It sounds like your rev limiter, most likely the one for the parking brake.
Forum: Yamaha
01-12-2007, 07:58 PM
Replies: 15
Views: 4,670
Posted By sixsixT

660 Raptor Vibration

Was there a locking tab washer behind the nut for the gear raptorgav? There should have been and they should not be reused. Always replace the washer if you loosen or take off that nut.
Forum: Yamaha
01-11-2007, 06:39 PM
Replies: 2
Views: 336
Posted By sixsixT

raptor big carb owners

I would use a pingle(sp) dual outlet petcock on it if you plan on running wide open for any length of time. Craycraft sells one that retains the reserve, not all do.
Forum: Yamaha
08-05-2006, 10:28 PM
Replies: 6
Views: 414
Posted By sixsixT

Raptor Valves

Yes what you've heard is true.I would check the exhaust valves since it's never been done before.
Forum: Yamaha
08-05-2006, 10:23 PM
Replies: 3
Views: 297
Posted By sixsixT

raptor is over heating! need help?

My guess would be a bad thermostat or a blown head gasket.Is the motor stock?
Forum: Yamaha
08-04-2006, 08:45 PM
Replies: 2
Views: 381
Posted By sixsixT

Raptor 660 One way question

If your talking about the gear that engages the oneway behind the flywheel I would replace it.
Forum: Yamaha
08-04-2006, 08:39 PM
Replies: 3
Views: 335
Posted By sixsixT

Raptor Balancer Prob

There should be a locking tab washer on that nut (the ones you bend up against one of the flat sides of the nut). And they should never be used twice, always replace them if you need to take off the...
Forum: Yamaha
06-15-2006, 08:11 AM
Replies: 2
Views: 391
Posted By sixsixT

ANY TIPS ON REMOVAL OF A STARTER CLUTCH AND FLYWHEEL ?? Anyone????

I'm guessing it's a raptor. Use a good puller on the flywheel, keep the flywheel nut on the threads flush with the end of the crank and when you have a good amount of tension on the puller give it a...
Forum: Yamaha
06-09-2006, 09:35 PM
Replies: 14
Views: 11,453
Posted By sixsixT

Yamaha raptor with 1000cc crotch rocket engine (pics!!!!)

I think that's the same one I bid on about 8 months ago on ebay. It had a turbo GSXR 1000 in it and need a little work to finish.
Forum: Yamaha
05-24-2006, 08:16 PM
Replies: 2
Views: 380
Posted By sixsixT

Raptor jetting help, back to stock

Stock is 140/145, I would go 145/150 with the filter mod.
Forum: Yamaha
05-24-2006, 08:10 PM
Replies: 4
Views: 348
Posted By sixsixT

lil prob with 660 lil help/advice please

LOL It might be a $30 part but hours of labor to put it in if you need to go inside the tranny.i/expressions/face-icon-small-tongue.gif
There's a knob on the right fender attached to a cable going...
Forum: Yamaha
05-23-2006, 09:15 PM
Replies: 2
Views: 398
Posted By sixsixT

Raptor Help Please!

It gets oil on it's own.
Forum: Yamaha
05-17-2006, 07:56 PM
Replies: 6
Views: 519
Posted By sixsixT

got +2 a arms,alignment problem

Did you remove your tie-rod ends from the spindles? If you put aftermarket ones back on and put the tie-rods on the top side of the mount instead of on the bottom side where they belong you'll get...
Forum: Yamaha
05-12-2006, 06:28 AM
Replies: 3
Views: 387
Posted By sixsixT

Raptor Transmission Question

I think the reverse problem your having is common. I always let the clutch out just a little and then push down on the shifter again to make sure it's fully engaged before I let the clutch all the...
Forum: Yamaha
05-09-2006, 10:30 PM
Replies: 6
Views: 329
Posted By sixsixT

Cam installation on raptor

Your mostly kinda right.i/expressions/face-icon-small-smile.gif A 4 stroke HAS to fire every 4th stroke or 2 revolutions but CAN fire every 2 strokes or every revolution, at the end of the...
Forum: Yamaha
05-09-2006, 09:45 PM
Replies: 4
Views: 301
Posted By sixsixT

Which one is the right Carb

This is my experience with the S1 cam.
My engine is all stock the only mods are:
Yoshi full exhaust
Modded carbs with GYTR needles
Port matched the intake
SixsixT dual K&N filter adapter

With...
Forum: Yamaha
05-09-2006, 08:32 PM
Replies: 4
Views: 301
Posted By sixsixT

Which one is the right Carb

Left is as you are sitting on it or shifter side.

My experience is different then most with the stage 1. I liked the stock cam better and put it back in. Need a slightly used S1...
Forum: Yamaha
05-09-2006, 08:18 PM
Replies: 6
Views: 329
Posted By sixsixT

Cam installation on raptor

It fires every revolution so it doesn't matter.
Forum: Yamaha
05-09-2006, 08:14 PM
Replies: 12
Views: 995
Posted By sixsixT

Help with my Raptor (very frustrating)

You can download the manual for free HERE (http://www.ljsoftware.com/Videos/Videos.htm) It's at the bottom of the page. Having a manual is great but it does have some incorrect info in it (float...
Forum: Yamaha
05-09-2006, 07:40 AM
Replies: 12
Views: 995
Posted By sixsixT

Help with my Raptor (very frustrating)

This is the best way.

The best thing to do is check it before you take it apart, with a piece of clear tubing. You can get the tubing at a hardware store for 20 cents, 1/8" clear tubing.

Thu...
Forum: Yamaha
05-01-2006, 07:43 PM
Replies: 6
Views: 551
Posted By sixsixT

lil problem with the carbs on a raptor

I think it was a common problem on the 01s and the boots or the clamps were different for 02s up. Some people have had luck with grinding a little off of the clamp spacer so it squeezes a little...
Forum: Yamaha
04-28-2006, 07:18 AM
Replies: 6
Views: 406
Posted By sixsixT

sheared off bolt in crankcase?

Did you try leaning the bike over to see if it will fall out?
Forum: Yamaha
04-26-2006, 07:53 AM
Replies: 8
Views: 451
Posted By sixsixT

Raptor Reverse light on/off

Sounds like a bad connection to the switch.
Forum: Yamaha
04-25-2006, 10:44 PM
Replies: 9
Views: 301
Posted By sixsixT

harmaonic balancer?

Hardware store
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.