Yamaha Discussions about Yamaha ATVs.

banshee help

Thread Tools
 
Search this Thread
 
Old Mar 22, 2009 | 03:34 PM
  #1  
jmdhoover's Avatar
Thread Starter
|
Weekend Warrior
Joined: Mar 2009
Posts: 2
Likes: 0
Default banshee help

i have a 01 banshee i had a new top end done and now it acts like its only runin off one cylinder any have a solution
 
Reply
Old Mar 22, 2009 | 04:24 PM
  #2  
JLsparky7's Avatar
Pro Rider
Joined: Mar 2004
Posts: 1,763
Likes: 0
Default banshee help

Where did you have the topend done?
What was replaced?
Did you install new plugs and gap them?
Whats the compression like on each clinder?
Have you tried switching coils?
 
Reply
Old Mar 22, 2009 | 05:06 PM
  #3  
jmdhoover's Avatar
Thread Starter
|
Weekend Warrior
Joined: Mar 2009
Posts: 2
Likes: 0
Default banshee help

i did the top end and everythang checked out great the carps sound like there suckin to much air
 
Reply
Old Mar 22, 2009 | 05:27 PM
  #4  
JLsparky7's Avatar
Pro Rider
Joined: Mar 2004
Posts: 1,763
Likes: 0
Default banshee help

Did you hone or bore the cylinders?
Did you replace the pistons or just the rings?
What do you mean everything checked out ok?
Any aftermarket parts?
Whats your jetting?
You didnt answer all the questions I asked the first time. We need more info to help you. You cant just post "my quad doesnt work" and expect us to figure out whats wrong.
 
Reply
Old Mar 22, 2009 | 05:40 PM
  #5  
91Warrior357's Avatar
Pro Rider
Joined: May 2008
Posts: 1,860
Likes: 0
From: Purcellville.
Default banshee help

yea you can try swapping the spark plug boots around and see if it makes the other side not fire, an incorrectly installed or not sealed head gasket could cause something like this also, and you need to try and answer some of JLsparkys questions, the more you can tell us the more we can help.
 
Reply
Old Mar 23, 2009 | 12:02 AM
  #6  
Ruthlesscoupe's Avatar
Weekend Warrior
Joined: Mar 2009
Posts: 3
Likes: 0
Default banshee help

i had the same prob with my 2001 shee at low to mid range it was doing it and then once i topped out it ran on both and i was goin nuts for a while everything was good compress plugs yada yada to make a long story short it was my air/fuel settings on one of the carbs after i fixed that its been fine since hope it helped
 
Reply
Old Aug 6, 2011 | 04:00 PM
  #7  
ninjachuckjr@gmail.com's Avatar
Weekend Warrior
Joined: Aug 2011
Posts: 1
Likes: 0
Default

we have replaced coil stator and plugs on 04 banshee still no fire can anyone help?
 
Reply
Old Aug 6, 2011 | 06:09 PM
  #8  
Jaster94's Avatar
Extreme Pro Rider
Joined: Jun 2009
Posts: 3,224
Likes: 9
From: Texas
Default

have you tested for an active ground? kill switch activated even though it shows "on" position? i.e. short circuit,,,,use a meter.
 
Reply
Old Aug 12, 2011 | 11:10 PM
  #9  
beerad's Avatar
Weekend Warrior
Joined: Aug 2011
Posts: 1
Likes: 0
Default

I bought a 2006 banshee and it is the first 2 stroke ive ever owned. also the only carb. bike ive ever owned. when the engine is cold it just will not start. but once it runs you can kill it and cranks on first kick after that until you allow it to sit over night. but i can put it in first gear and bearly push it and cranks up fine. Can anyone maybe give me a pointer on this? Seems like this small problem makes me wish they made the banshee with fuel injection.
 
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Kaleb_00
Performance Mods and Project Quads
2
Jun 1, 2016 09:15 AM
greek271
Yamaha
2
Aug 8, 2015 08:16 PM
JohnnySplat
Yamaha
6
Aug 6, 2015 12:07 PM
Dirtbikemike1
General Chat
1
Jul 11, 2015 03:36 PM
ATVC Correspondent
Classifieds, Garage Sale & Swap Shop
0
Jul 7, 2015 11:00 PM

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 



All times are GMT -5. The time now is 03:02 AM.