Brute sunk totally....steps to flush?
#3
![Default](https://atvconnection.com/forums/images/icons/icon1.gif)
Youthguy
As soon as possible, drain oil/gas, Pull plugs. Inspect cylinder for mud (May have to flush out with hose) & use pull start to turn over engine/get all water out of cylinders.
Once all water is removed squirt cylinder with small squirt of oil and pull start again to coat cylinder wall and then remove pull starter housing, drain water, dry & reinstall.
Remove & Put battery on charger while you are cleaning Quad
Drain gastank, Remove drain blow out Muffler/exhausts, remove/clean carb bowls, slides, springs, jets & needle jets, and pilot jets, CVT cover. Use air source/blowgun and spray low pressure bursts of air in all jet openings near/in carbs and inside airbox & drain & blow out all drain lines/vaccum lines leading to airbox. Disconnect fuel line from petcock to gas tank and petcock to carbs
Thouroughly clean carb bowls, jets, remove/flush mud/dirt from inside CVT, belt, & clutches. Blow dry and inspect all fuses, wiring harness, slightly bend end on fuse, smear with diaelectric grease & Inspect/re-insert all fuses
Reassemble, Put in fresh gas, plugs, cheap oil/filter, & reconnect battery. Ensure CVT cover is installed before turning on key. Turn on key & let fuel pump out fuel line from tank, connect line to petcock and let full pump out line from petcock while cycling petcock. Reconnect carbs, full choke, engine kill switch off, and fire up. Run till fan kicks on and Change oil & filter. Repeat oil/filter change till no water is in oil put in favorite synthetic oil & good filter.
Buy a boat for water above 3 feet.
[img]i/expressions/face-icon-small-blush.gif[/img]
Happy trails
As soon as possible, drain oil/gas, Pull plugs. Inspect cylinder for mud (May have to flush out with hose) & use pull start to turn over engine/get all water out of cylinders.
Once all water is removed squirt cylinder with small squirt of oil and pull start again to coat cylinder wall and then remove pull starter housing, drain water, dry & reinstall.
Remove & Put battery on charger while you are cleaning Quad
Drain gastank, Remove drain blow out Muffler/exhausts, remove/clean carb bowls, slides, springs, jets & needle jets, and pilot jets, CVT cover. Use air source/blowgun and spray low pressure bursts of air in all jet openings near/in carbs and inside airbox & drain & blow out all drain lines/vaccum lines leading to airbox. Disconnect fuel line from petcock to gas tank and petcock to carbs
Thouroughly clean carb bowls, jets, remove/flush mud/dirt from inside CVT, belt, & clutches. Blow dry and inspect all fuses, wiring harness, slightly bend end on fuse, smear with diaelectric grease & Inspect/re-insert all fuses
Reassemble, Put in fresh gas, plugs, cheap oil/filter, & reconnect battery. Ensure CVT cover is installed before turning on key. Turn on key & let fuel pump out fuel line from tank, connect line to petcock and let full pump out line from petcock while cycling petcock. Reconnect carbs, full choke, engine kill switch off, and fire up. Run till fan kicks on and Change oil & filter. Repeat oil/filter change till no water is in oil put in favorite synthetic oil & good filter.
Buy a boat for water above 3 feet.
[img]i/expressions/face-icon-small-blush.gif[/img]
Happy trails
#5
![Default](https://atvconnection.com/forums/images/icons/icon1.gif)
Thanks Man...The LCD was my worry, but is drying and gonna partly work. Lot's of work to a drowned rat........I'll check it all out tomorrow. 30 hours after happening. I changed oil on the river and got it out of the cylinders then as well.....thanks alot!
#6
#7
Trending Topics
#10
Thread
Thread Starter
Forum
Replies
Last Post
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)