My TB Pics...
Apr 10, 2002 | 08:39 PM
#1
Thread Starter
|
Trailblazer
Joined: Nov 2001
Posts: 89
Likes: 0
Pics of my 98 TB So far, what do you guys think???
New Link below.......
http://photos.yahoo.com/bc/stinkybla...c=ph%26.view=l
New Link below.......
http://photos.yahoo.com/bc/stinkybla...c=ph%26.view=l
Apr 10, 2002 | 10:35 PM
#5
Trailblazer
Joined: Mar 2002
Posts: 100
Likes: 0
Apr 11, 2002 | 12:10 AM
#6
Thread Starter
|
Trailblazer
Joined: Nov 2001
Posts: 89
Likes: 0
For some reason yahoo is not letting me make my photos for everyone to view, when I take it off private and change to all to view it changes back to private by itself.
Try this......
http://photos.yahoo.com/bc/stinkybla...c=ph%26.view=l
Try this......
http://photos.yahoo.com/bc/stinkybla...c=ph%26.view=l
Apr 11, 2002 | 12:42 AM
#7
Range Rover
Joined: Jan 2001
Posts: 139
Likes: 0
Your tblazer looks great! How did you make the nerf bars? How do you like the Dirt Devils? I lookin at puttin a set on the Xpress.
Trending Topics
Apr 11, 2002 | 01:44 AM
#8
Thread Starter
|
Trailblazer
Joined: Nov 2001
Posts: 89
Likes: 0
Hi Express,
The dirt devils are O.K, I know its silly but I prefered my half worn titans, maybee I just like drifting sideways more. Dirt devals are ave good in the mud though....
First removed my floor boards, cut my plastics,
I went and brought 2.0m of 1 1/4" alloy tube, from my local engineer,
Made cardboard templates to get it looking right,
Then took cardboard & pipe to local exhaust shop, 2 bends in each side.
Also got him to weld (feet) on the bars, then went home ab drilled them into the frame & bolted.
Then thought for a long time what to use, in the end I got 1 sq m of security door mesh, shaped and welted in to place, I was going to use normal nerf mesh, but I wanted it to be alot stronger, also alloy mesh is very light.
Total cost of about $40 NZ, prob about $20 USA.
I just could not justify spending about $750 NZD to send over from the US.
Anyway hope this helps, thanks for your comments....
The dirt devils are O.K, I know its silly but I prefered my half worn titans, maybee I just like drifting sideways more. Dirt devals are ave good in the mud though....
First removed my floor boards, cut my plastics,
I went and brought 2.0m of 1 1/4" alloy tube, from my local engineer,
Made cardboard templates to get it looking right,
Then took cardboard & pipe to local exhaust shop, 2 bends in each side.
Also got him to weld (feet) on the bars, then went home ab drilled them into the frame & bolted.
Then thought for a long time what to use, in the end I got 1 sq m of security door mesh, shaped and welted in to place, I was going to use normal nerf mesh, but I wanted it to be alot stronger, also alloy mesh is very light.
Total cost of about $40 NZ, prob about $20 USA.
I just could not justify spending about $750 NZD to send over from the US.
Anyway hope this helps, thanks for your comments....
Apr 11, 2002 | 03:30 AM
#10
Thread Starter
|
Trailblazer
Joined: Nov 2001
Posts: 89
Likes: 0
he he, good spotting, I got so sick of adjusting the dammn thing, I took the whole thing off, it is an 98 so disc was on side of crankcase.
I have got a rear axle & brake setup from an 01 Blazer in my shed to put on, But I am still not gonna put foot brake control back on, just an extra hand control. (also any races I do I am required to have rear brake, so I must get on to that).
I have got a rear axle & brake setup from an 01 Blazer in my shed to put on, But I am still not gonna put foot brake control back on, just an extra hand control. (also any races I do I am required to have rear brake, so I must get on to that).
Thread
Thread Starter
Forum
Replies
Last Post
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
