whats in your garage?
#4421
08-19-2009, 11:58 AM
Pro Rider
Is always changing bikes.
Is always changing bikes.
Join Date: Oct 2006
Posts: 444
Likes: 0
Received 0 Likes
on
0 Posts
ATV Drag Racers
ATV Drag Racers
ATV Drag Racers
its for sale! mainly just because i have lost interest due to some certain reasons.
Chassis
lightened stock frame
chromoly subframe built by The FOG
wheelie bar built by The FOG
Drag Steering stem built by The FOG
Chromoly A-arms and spindles
CP Customs +4 swingarm
shaws all around
aluminum battery/electronics box mounted under the seat
Douglas 10x2 spindle mounts with 18" buffs
JJ&A drag axle
a set of 4-snows on ITP .190s will come on the rear
PERFORMANCE
Stock motor, with fresh rings gapped for nitrous
Vortex ignition programmed for Motor curve and Nitrous curve
48mm Mikuni HSR carb and ported intake
Pingle Fuel valve
Ron wood drag pipe
520 9800lb chain and sprockets
Boondockers Nitrous kit on full throttle switch
Barnett 9 disk kevlar clutch kit
did some bracket racing this weekend. track was hard and 60fts were off for everyone. my last pass the guy red lit (first infraction) so i ran it out the back door with a 1.778 60ft 59.xx mph @ 5.10 et ON STOCK MOTOR, no nitrous!!!!
before it was set up on a 15hp shot and was picking up 4 tenths on the spray. it now is set up on the 20, just havnt had it at the track on the spray since!
still has more in it track was just tight and the tires wouldnt get down and dig off the line!
$4,000
ATV Drag Racers
ATV Drag Racers
its for sale! mainly just because i have lost interest due to some certain reasons.
Chassis
lightened stock frame
chromoly subframe built by The FOG
wheelie bar built by The FOG
Drag Steering stem built by The FOG
Chromoly A-arms and spindles
CP Customs +4 swingarm
shaws all around
aluminum battery/electronics box mounted under the seat
Douglas 10x2 spindle mounts with 18" buffs
JJ&A drag axle
a set of 4-snows on ITP .190s will come on the rear
PERFORMANCE
Stock motor, with fresh rings gapped for nitrous
Vortex ignition programmed for Motor curve and Nitrous curve
48mm Mikuni HSR carb and ported intake
Pingle Fuel valve
Ron wood drag pipe
520 9800lb chain and sprockets
Boondockers Nitrous kit on full throttle switch
Barnett 9 disk kevlar clutch kit
did some bracket racing this weekend. track was hard and 60fts were off for everyone. my last pass the guy red lit (first infraction) so i ran it out the back door with a 1.778 60ft 59.xx mph @ 5.10 et ON STOCK MOTOR, no nitrous!!!!
before it was set up on a 15hp shot and was picking up 4 tenths on the spray. it now is set up on the 20, just havnt had it at the track on the spray since!
still has more in it track was just tight and the tires wouldnt get down and dig off the line!
$4,000
link to pic's and build topic
#4423
08-19-2009, 09:45 PM
#4424
08-23-2009, 08:30 PM
#4425
08-28-2009, 04:38 PM
Pro Rider
I'm a Plumbing contractor and I have some old friends that always called me Pipelayer for some reason?
I'm a Plumbing contractor and I have some old friends that always called me Pipelayer for some reason?
Join Date: Aug 2006
Posts: 339
Likes: 0
Received 0 Likes
on
0 Posts
#4426
08-29-2009, 12:00 AM
#4427
08-29-2009, 01:17 AM
#4429
08-31-2009, 07:53 AM
Pro Rider
Join Date: Mar 2009
Location: Upstate NY. Near Albany
Posts: 380
Likes: 0
Received 0 Likes
on
0 Posts
I have an 05 engine, a set of works front shocks, almost new headlight (fits older style), red, black, & orange sets of plastic, Pro Circuit T-4 pipe, & an air box with filter & hoses. skidooguy30m@yahoo.com
#4430
09-03-2009, 12:37 AM