Where Should I Go For A Case Half?
#1
![Default](https://atvconnection.com/forums/images/icons/icon1.gif)
As most of you may know, I busted my 250R's left case half, and now I can afford to get a new one. I've seen guys in here that say they've bought new halves, and I want to know where they're hiding them!
Service Honda has 87's, and K&K has 86's, but I cannot find an 89! Do they all match up? Anyone done the swap(pre 89's on an 89)?
Thanks for everyone's help. I will be sure to take pictures along the way, and fill everyone in, and yes, there will be more questions soon!
Service Honda has 87's, and K&K has 86's, but I cannot find an 89! Do they all match up? Anyone done the swap(pre 89's on an 89)?
Thanks for everyone's help. I will be sure to take pictures along the way, and fill everyone in, and yes, there will be more questions soon!
#2
![Default](https://atvconnection.com/forums/images/icons/icon1.gif)
87 and 86 will not work because they have different part numbers but the 88 and 89 have the same part number so i would imagine that the 88 would fit the 89 because they both have the same part number go to rivayamaha and look at the micro fiche and check it out i just check out service hondas web site and it says the left crank half goes for 182 check it out here and type in the honda part number 11200-hb9-771 that i got fromhonda part numbers at rivayamaha i hope this helps and good luck on your rebuild
#3
![Default](https://atvconnection.com/forums/images/icons/icon1.gif)
I just got done reading a DirtWheels mag and remembered seeing ads in there for "discount" parts. Here are a couple websites Western Honda then there are used parts at Cycle Pros Salvage and Quad Pros All-Terrain Cycle sorry I couldn't answer your real question, just tryin to help.
#6
![Default](https://atvconnection.com/forums/images/icons/icon1.gif)
Hey Corey, long time no see!
I talked to Tim the other day, and his cases are $280 without bearings. I was planning on going with K&K's, because they come with bearings, but the only cases they have are 86's.
Corey, will you be at Badlands tomorrow? I guess I might take the Banshee back up there.
I talked to Tim the other day, and his cases are $280 without bearings. I was planning on going with K&K's, because they come with bearings, but the only cases they have are 86's.
Corey, will you be at Badlands tomorrow? I guess I might take the Banshee back up there.
#7
Trending Topics
#8
![Default](https://atvconnection.com/forums/images/icons/icon1.gif)
I agree with Dill.From what I've been told, you shouldn't mix-n-match case halves as they are "matched". Unfortunatley,if I were you I would go and get both sides and play it safe rather than having a leaker.Also another thing to consider is where it may leak.Oil is bad enough,but getting an air leak in the actual crankcase will lean it out = no idle and maybe burning her down.Good luck,Jim
#9
![Default](https://atvconnection.com/forums/images/icons/icon1.gif)
I went ahead and ordered one from Service Honda. They were the cheapest.. rang up to $194.44 shipping included. They said it would be here in a week and a half, so I'm pleased. Now all I will have to do is order a seal/gasket set.
Could I run a small bead of high temp silicon around the case seal.. Just to give me a little insurance? Thanks for your help.
Could I run a small bead of high temp silicon around the case seal.. Just to give me a little insurance? Thanks for your help.
#10
Thread
Thread Starter
Forum
Replies
Last Post
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)