85 to 88 Suzuki LT230S Quadsport help.
were can i buy jets for my 230s? i put my dg exhaust on and its backfiring and shooting flame *****. put a new plug in and its black but from what im reading its a lean backfire. so i would like to buy a couple jets that are a few different sizes bigger to start the process of re jetting it but i cant find any jets for it online. if anybody has a link or can give me info of the right jet to get that would be great. right now im running the stock filter but after winter it will have a uni air filter so i wanna buy jets that will work good with the dg pipe and the uni filter.
Do a search on ebay for "lt230s jet kit" and you'll come up with one result. It's a 6sigma jet kit that says it includes everything. For about $50 shipped I don't know if it's worth the gamble though...
I never had to rejet my carb after installing the uni filter and dg pipe, just had to make a few adjustments on the carb. I remember I had to turn the fuel screw out a little more and I can't remember if I had to move the clip on the needle...I believe I had to move the clip down a notch which raised the needle a little higher.
I never had to rejet my carb after installing the uni filter and dg pipe, just had to make a few adjustments on the carb. I remember I had to turn the fuel screw out a little more and I can't remember if I had to move the clip on the needle...I believe I had to move the clip down a notch which raised the needle a little higher.
@nate85
How did the installation process go for you when you installed the pipe? Mine was a freaking nightmare...I hate having to modify parts that are supposed to "bolt-on." I even went as far as to contact the seller and verifying measurements that they sent me the right part. I was told they were all the same and, seeing as how these parts won't be available forever, I decided to just make it work.
How did the installation process go for you when you installed the pipe? Mine was a freaking nightmare...I hate having to modify parts that are supposed to "bolt-on." I even went as far as to contact the seller and verifying measurements that they sent me the right part. I was told they were all the same and, seeing as how these parts won't be available forever, I decided to just make it work.
Do a search on ebay for "lt230s jet kit" and you'll come up with one result. It's a 6sigma jet kit that says it includes everything. For about $50 shipped I don't know if it's worth the gamble though...
I never had to rejet my carb after installing the uni filter and dg pipe, just had to make a few adjustments on the carb. I remember I had to turn the fuel screw out a little more and I can't remember if I had to move the clip on the needle...I believe I had to move the clip down a notch which raised the needle a little higher.
I never had to rejet my carb after installing the uni filter and dg pipe, just had to make a few adjustments on the carb. I remember I had to turn the fuel screw out a little more and I can't remember if I had to move the clip on the needle...I believe I had to move the clip down a notch which raised the needle a little higher.
@nate85
How did the installation process go for you when you installed the pipe? Mine was a freaking nightmare...I hate having to modify parts that are supposed to "bolt-on." I even went as far as to contact the seller and verifying measurements that they sent me the right part. I was told they were all the same and, seeing as how these parts won't be available forever, I decided to just make it work.
How did the installation process go for you when you installed the pipe? Mine was a freaking nightmare...I hate having to modify parts that are supposed to "bolt-on." I even went as far as to contact the seller and verifying measurements that they sent me the right part. I was told they were all the same and, seeing as how these parts won't be available forever, I decided to just make it work.
just googled what you said for the jet kit and came across these sticker kits. these look badass http://www.amrracing.com/catalog/qua...years-233.html
Nice find on those stickers
Ok the issue I had with installing the dg system was with the headpipe. When I took the old exhaust system off I also pulled out the gasket which was pretty well toast. After driving 45 minutes one way to get a new one I put it in, put the headpipe on, and proceeded to loosely bolt the flange on. Only one problem. Either the studs were too short or the "wider section" on the headpipe was way different. That's when I started comparing the new with the old and I realized I had to modify the new pipe. Long story short I cut the "motor end" of the pipe shorter so I could bolt it on using the original studs. Looking back I could have replaced the 2 studs with longer ones but that could have led to even more headaches.
Being that you had to smash the gasket just to get it together you could very well have an issue at that connection which I hope is not the problem in your case! Good luck getting it dialed in!
These pipes do make em sound mean don't they If I ever come up with a solution for a spark arrestor for them I'll be sure to post it here!
Ok the issue I had with installing the dg system was with the headpipe. When I took the old exhaust system off I also pulled out the gasket which was pretty well toast. After driving 45 minutes one way to get a new one I put it in, put the headpipe on, and proceeded to loosely bolt the flange on. Only one problem. Either the studs were too short or the "wider section" on the headpipe was way different. That's when I started comparing the new with the old and I realized I had to modify the new pipe. Long story short I cut the "motor end" of the pipe shorter so I could bolt it on using the original studs. Looking back I could have replaced the 2 studs with longer ones but that could have led to even more headaches.
Being that you had to smash the gasket just to get it together you could very well have an issue at that connection which I hope is not the problem in your case! Good luck getting it dialed in!
These pipes do make em sound mean don't they If I ever come up with a solution for a spark arrestor for them I'll be sure to post it here!
Some wire screen poked inside the muffler to give it more surface area will work as a spark arrestor.
I used to get jets from bikebandit, but you have to buy 4. Most places you will have to buy 4. For single jets, go to a dealer. Any dealer except honda. Honda has keihin parts that won't work.
I would lean out the main or lower the needle (raise the clip) and either turn out the mixture screw or install a larger pilot.
I used to get jets from bikebandit, but you have to buy 4. Most places you will have to buy 4. For single jets, go to a dealer. Any dealer except honda. Honda has keihin parts that won't work.
I would lean out the main or lower the needle (raise the clip) and either turn out the mixture screw or install a larger pilot.
If I can order a screen that is the same diameter as the inside of the muffler then I could get one that is USFS approved which would be the right way to do it. Then I could make an endcap similar to what malhombre has on his 230. I asked him awhile back and he said his mechanic got him a USFS approved spark arrestor screen but he doesn't know where he got it and doesn't have a part number for it. I'll get it eventually lol. The only reason I'm being so cautious is because I almost got the quad confiscated by the michigan dnr back in 06 while riding on atv trails through state land. He got done looking it over and said "everything looks good but without a spark arrestor I'm gonna have to shut you down for the day" He let my buddy tow me back to the truck approximately 6 miles away at the staging area while he followed. He then waited for us to load up and head out.
you have this one that may work
DG Performance Bullet Exhaust Replacement Spark Arrestor 98 9105 | eBay
or this one
DG Performance 98 9103 Replacement Spark Arrestor RCM II Slip on Exhaust | eBay
but not sure if either would work
DG Performance Bullet Exhaust Replacement Spark Arrestor 98 9105 | eBay
or this one
DG Performance 98 9103 Replacement Spark Arrestor RCM II Slip on Exhaust | eBay
but not sure if either would work