Yamaha Discussions about Yamaha ATVs.

how do I correctly remove the tors on blaster?

  #1  
Old 09-05-2006, 10:12 AM
Weekend Warrior
Thread Starter
Join Date: Aug 2006
Posts: 13
Default how do I correctly remove the tors on blaster?

I just bought a new 28mm d slide carb for my wife's blaster and need to run without the tors system. I removed the whole assembly on top of the old carb including the small switch, but the thing doesn't want to start let alone idle when I do get it to start. What do I need to do, if anything, with the small switch inside the thumb throttle assembly? also all I did with the wires that went to the old switch on top of the carb was disconnect the plug and leave it. Do I need to jumper these out or something? Thanks.
 
  #2  
Old 09-05-2006, 01:23 PM
Weekend Warrior
Thread Starter
Join Date: Aug 2006
Posts: 13
Default how do I correctly remove the tors on blaster?

Noone here has removed this system? Surely it can't be all that uncommon to ditch this crap?
 
  #3  
Old 09-05-2006, 07:35 PM
Pro Rider
Join Date: May 2006
Posts: 434
Default how do I correctly remove the tors on blaster?

what is a tors system???
 
  #4  
Old 09-05-2006, 07:46 PM
Weekend Warrior
Thread Starter
Join Date: Aug 2006
Posts: 13
Default how do I correctly remove the tors on blaster?

Maybe I have mispelled it but that darned close. This is the system with a switch at the throttle assembly and a switch on the top of the carb which has something to do with controlling the idle. My new carb does that the old fashioned way and I need to remove the entire old system beforee the quad will idle at all or run properly.
 
  #5  
Old 09-05-2006, 09:13 PM
Pro Rider
Join Date: Dec 2004
Posts: 334
Default how do I correctly remove the tors on blaster?

At the thumb throttle assembly take the switch out and splice the wires. The wires that go to the carb just need to be diconnected. Here is some pictures of what to do TORS Removal
 
  #6  
Old 09-06-2006, 12:16 AM
JLsparky7's Avatar
Pro Rider
Join Date: Mar 2004
Posts: 1,763
Default how do I correctly remove the tors on blaster?

Disconnect the wires that are attached to the box under the front left fender attached to the frame.

Cut the wires on the bottom of the silver part on the peice of top of the carb.

Cut the wires going to your throttle box on your handlebars

Trace all these wires and there should be plugs (under the tank) were you can unplug and completely detach them.

Reset your idle and you might have to mess with your air mixture screw, then your all set. that post above is a great link as well.
 
  #7  
Old 09-07-2006, 08:09 AM
Weekend Warrior
Thread Starter
Join Date: Aug 2006
Posts: 13
Default how do I correctly remove the tors on blaster?

I don't see a box under the left fender, but under the front cover there are three. Are you referring to the plastic box with the three pin connector that has a yellow, black, and a black with white tracer? These are at least very similar to the ones going to the switches for the tors system but none have continuity with the wires going to the switches. I have tried disconnecting all this stuff and still cannot get this thing to start, not even to sputter. All I did was change the carb, but now I don't seem to have any spark.
 
  #8  
Old 09-07-2006, 02:18 PM
JLsparky7's Avatar
Pro Rider
Join Date: Mar 2004
Posts: 1,763
Default how do I correctly remove the tors on blaster?

It should be inside the left front fender attached to the frame. There is 1 philips screw holding it on. Its a 1inch by 2 inch black box. Not sure on the color wires. The previous owner might have taken it out already. Your idle might not be high enough on the quad eighter since you changed the carb. Try turning that up. Take a look at your reeds too. Is it getting a spark?
 
  #9  
Old 09-07-2006, 08:52 PM
Pro Rider
Join Date: Dec 2004
Posts: 334
Default how do I correctly remove the tors on blaster?

Did you splice the wires that go to the the thumb throttle assembly?Whether you remove the box or not shouldn't have any effect since you've disconnected it.
 
  #10  
Old 05-24-2019, 11:10 AM
Trailblazer
Join Date: May 2019
Location: Michigan
Posts: 45
Default

If you are not looking to buy the kit to replace it follow this video here to bypass the TORS
 
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
slowgsxr97
Polaris
13
09-08-2015 04:37 AM
scott1988
Yamaha
9
08-18-2015 08:44 AM
Cantbuytime
Drivetrain, Suspension & Tires
0
08-16-2015 09:13 PM
315blaster
Other ATV Topics
0
08-08-2015 08:13 PM
drewy2dope
Ask the Editor
11
07-31-2015 09:36 AM

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 

Thread Tools
Search this Thread
Quick Reply: how do I correctly remove the tors on blaster?


Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.
 
  • Ask a Question
    Get answers from community experts
Question Title:
Description:
Your question will be posted in: